The Basics of Plumbing Skills for Bathtub Installation
The Basics of Plumbing Skills for Bathtub Installation
Blog Article
Just how do you feel when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a tub isn't exactly brain surgery, however it does need solid plumbing, carpentry, and often, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably tough project. If the old tub is readily easily accessible, the task can relocate immediately; if you have to open a wall surface to get rid of the old tub as well as position the new tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to move out the old tub as well as set in the brand-new one. Ensure you have actually qualified yourself for the task and also fit attempting it. Instead of hiring a contractor to take control of a halfway-completed job, it is better to take into consideration utilizing one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This article will certainly assist you install a new bath tub in your shower room if you have currently purchased a brand-new bathtub and also don't need to alter the plan of your previous supply of water pipes.
Your devices and also product list need to make up the following:
Getting ready for the Installment
Firstly, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the tap features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps system to avoid stress on the bath tub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you utilize all of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its last setting.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The procedure of removing the existing taps can be quite problematic as a result of the restricted accessibility that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a towel all set for the staying water that will originate from the pipelines. When the supply pipes have actually been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming throughout this process. Once the taps have been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing compound.
Before carrying on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Using both wooden boards under its feet, place the tub in the required setting. The wood boards are useful in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little points.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the tub till the level reads degree.
To install taps, fit the bottom of the outermost adaptable faucet port to the ideal supply pipeline by making a compression sign up with; then do the same for the other tap.
Activate the water system and also examine all joints and also new pipework for leaks and also tighten them if required. Fill up the bathtub as well as likewise inspect the overflow electrical outlet and also the normal electrical outlet for leaks.
Finally, repair the bathroom paneling as described in the maker's user's manual. Tiling and also sealing around the tub ought to wait till the bathtub has actually been utilized a minimum of when as this will certainly settle it into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washing machines remain in area in between the faucet and also the sink. Secure the faucet in place with the maker offered backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The former type needs to be linked to the faucet ends first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to break a rigid seal, creating the water to pass through the wall surface in between the bath and the tiling, bring about difficulties with moisture and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes as well as cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily available on the marketplace. It is a good idea to fit the tiles using waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was made aware of that editorial on Tools You Need to Install a New Bathtub through a friend on our other web blog. Feel free to take a moment to promote this blog posting if you enjoyed it. Thank-you for your time invested reading it.
Expertly handling plumbing emergencies daily. Report this page